A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
How do you feel when it comes to How to Install a Bathtub?
Mounting a bathtub isn't exactly rocket science, but it does require solid plumbing, woodworking, and also sometimes, tiling abilities. Changing an old bathtub with a new one is also a reasonably hard job. If the old bathtub is easily easily accessible, the project can relocate quickly; if you have to open up a wall surface to remove the old tub as well as place the brand-new bathtub, the task is a lot harder. In either instance, the job is within a house handyman's abilities, although you will require a helper to leave the old tub as well as embeded in the brand-new one. Make certain you have qualified yourself for the task and also are comfortable attempting it. As opposed to hiring a specialist to take over a halfway-completed project, it is far better to consider employing one prior to you begin. Possibilities are you may require an expert plumber to make tube links.
This short article will certainly aid you mount a new bath tub in your restroom if you have actually already purchased a new bathtub and do not require to change the plan of your previous supply of water pipelines.
Your tools and product list must make up the following:
Planning for the Setup
Firstly, the sustaining framework supplied with the bath should be fitted (if needed) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is important to see to it that if the tap features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps unit to stop pressure on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the provided washers.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its last placement.
Removing Old Touches
If you need to change old taps with new ones as a part of your setup, then the first thing you should do is disconnect the water supply. After doing so, switch on the taps to drain pipes any type of water staying in the system. The procedure of removing the existing faucets can be quite bothersome because of the restricted access that is usually the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a cloth ready for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from turning during this process. When the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing substance.
Before going on to fit the new faucets, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Making use of the two wood boards under its feet, put the bathtub in the needed setting. The wooden boards are handy in uniformly spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 tiny factors.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by checking the level and also changing the feet on the tub up until the level reviews level.
To mount faucets, fit the bottom of the outermost adaptable faucet port to the proper supply pipeline by making a compression join; then do the very same for the other faucet.
Turn on the water system and check all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill the bathtub as well as likewise examine the overflow electrical outlet and the normal outlet for leakages.
Finally, fix the bath paneling as explained in the producer's instruction manual. Tiling and also securing around the bathtub needs to wait up until the bath tub has been used a minimum of once as this will settle it right into its last setting.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the mounting hole in the bath/basin ensuring that the washing machines are in location between the tap as well as the sink. Protect the tap in position with the manufacturer offered backnut. Once the faucet is securely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular faucet ports. The previous type needs to be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to fracture an inflexible seal, creating the water to pass through the wall surface between the bath and also the tiling, leading to complications with wetness as well as possible leakages to the ceiling listed below.
You can select from a range of coloured sealers to blend in your fixtures as well as fittings. They are offered in tubes and also cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of soaked newspaper or soft rope. Keep in mind to always fill the tub with water before securing, to enable the activity experienced when the bathtub remains in use. The sealer can crack rather early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also easily offered on the market. It is a good idea to fit the floor tiles utilizing water-resistant or water resistant glue as well as cement.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
I hope you liked our article about A Step-by-Step Guide to Installing a Bathtub. Thanks a ton for spending some time to read through our blog. For those who enjoyed our blog posting kindly make sure you remember to pass it around. Thank you for your time. Come back soon.
Immediate assistance? Ring! Report this page